Afilador múltiple de hojas de sierra Freedom
Patent Pending • Jobsite blade sharpener

Afilador múltiple de hojas de sierra Freedom

Patent Pending

Stop throwing away blades you can reclaim in seconds or minutes.

Built in Michigan30-day guaranteeReal customer proof below

Stop throwing away blades you could sharpen in seconds.

Read customer reviews

Reclaim the blades you already paid for, build a ready-to-swap stockpile, and slash your blade costs over time.

Whether dull blades are piling up in your truck or going straight into the trash, the result is the same: paid-for blade value is being lost. JobSaver Pro helps you put that value back to work quickly.

Sharpening has to make financial sense. This does. Many touch-ups take only seconds, and larger, more expensive blades can often be reclaimed in just a few minutes.
  • Oscillating blades can often be sharpened in about 10–30 seconds.
  • Reciprocating blades can often be sharpened in about 30 seconds.
  • A 10-inch circular or miter saw blade typically takes about 5 minutes; a 12-inch blade about 7 minutes.
Patent pending

Original JobSaver Pro. Patent-pending design.

This is not a generic copycat sharpener. JobSaver Pro is Tiger’s Teeth’s patent-pending blade-sharpening system, built for contractors who want the real tool, real support, and real jobsite proof.

Stop losing blade value

You are either storing dull paid-for blades — or throwing them away.

If they are sitting in a bucket, your money is trapped in blades you cannot use. If they are going in the trash, your money is leaving with them.

1

Sharpen fast enough for the math to work

Most touch-ups take seconds, or just a few minutes for larger, more expensive blades, so the time invested can be far less than the replacement cost.

2

Reclaim what you already paid for — and stop buying so many new blades

Whether dull blades are sitting in a bucket or going straight into the trash, put them back to work and reduce how often you need to buy replacements.

3

Build a ready-to-swap stockpile

Sharpen blades in batches, keep them ready for the next job, and use on-site sharpening only when the unexpected happens.

Every blade you throw away while waiting to order JobSaver Pro is another blade you will likely pay to replace. The sooner you order and put JobSaver Pro into your workflow, the sooner you can stop paying to replace blades that could have been sharpened.

See what you can reclaim, sharpen, and put back into rotation.

Each dropdown shows the sharpening process, typical replacement cost, and sharpening time so you can see how quickly reclaimed blades can build a useful backup inventory.

Most common demoOscillating multi-tool blades
Sharpening individual teeth on an oscillating multi-tool blade with JobSaver Pro
Typical replacement cost: $3–$19 each Typical sharpening time: A few seconds for routine touch-ups

The first re-toothing can take longer; once the new tooth profile is established, future sharpening is fast.

Create a new row of razor-sharp teeth on the blade. Once the new profile is on there, sharpening should only take a few seconds each time.

1. Remove worn original teeth2. Create new row of teeth3. Go back to work cutting
Side wheel setupHole saws
Sharpening a hole saw with JobSaver Pro
Typical replacement cost: $10–$50+ each Typical sharpening time: About 1–4 minutes

Larger or heavily worn hole saws may take longer.

Find the approximate angle of the teeth, then lightly grind the worn tooth edges so the hole saw cuts instead of burning, skating, and wasting time.

1. Find angle2. Lightly grind3. Cut cleaner
Platinum packageCircular / miter saw blades
Sharpening a circular or miter saw blade with JobSaver Pro
Typical replacement cost: $20–$100+ each Typical sharpening time: About 3–5 minutes

Time varies with blade diameter, tooth count, and how many teeth need attention.

Touch up worn tooth edges so the blade cuts cleaner and lasts longer before you buy another one.

1. Index tooth2. Touch edge3. Rotate blade
Platinum packageReciprocating saw blades
Sharpening a reciprocating Sawzall blade with JobSaver Pro
Typical replacement cost: $3–$15 each Typical sharpening time: About 30 seconds

A quick touch-up can keep the blade biting instead of sending another blade to the trash.

Bring worn reciprocating teeth back to a working edge in about 30 seconds so the blade keeps biting instead of skating and slowing the job down.

1. Align teeth2. Touch up3. Keep cutting
Platinum packageDrill bits
Sharpening a drill bit with JobSaver Pro
Typical replacement cost: $3–$20+ each Typical sharpening time: About 10–20 seconds

Larger, premium, or heavily damaged bits may take longer than the typical 10–20 second touch-up.

Touch up worn drill bit cutting edges so the bit can bite again instead of slipping, smoking, or wasting time.

1. Set angle2. Touch edge3. Drill again
Package comparison

Choose the package that matches the blades you want to sharpen.

Choose the package that matches the blade types you want to reclaim, stockpile, and keep ready for future jobs.

JobSaver Pro Platinum package contents
Recommended
Platinum
Full saw blade sharpening setup

Choose Platinum if you want the broadest saw blade sharpening setup for oscillating blades, hole saws, circular/miter saw blades, reciprocating saw blades, drill bits, and more.

  • Everything in Gold
  • Best for contractors
  • Broadest saw blade-sharpening capability
JobSaver Pro Gold package contents
Gold
Oscillating blades + side-wheel touch-ups

Choose Gold if you want the Basic setup plus side wheels for faster touch-ups and more sharpening flexibility.

  • Everything in Basic
  • 60° CBN side wheel for steel/bi-metal
  • 60° diamond side wheel for carbide
JobSaver Pro Basic package contents
Basic
Steel / bi-metal oscillating blades

Choose Basic if you mainly want to bring steel or bi-metal oscillating multi-tool blades back to life.

  • Main grinding wheel setup
  • Best entry package
  • For steel/bi-metal oscillating blades
Stay on the jobNo more wasted trips for replacement blades.
Sharpen on demandBring dull blades back before work stops.
Build backupsRe-sharpen dull stock during downtime.
Zero risk30-day money-back guarantee.

The cost does not stop while you think about it.

Another blade gets dull. Another replacement gets opened. Another paid-for blade goes into the bucket or trash. Waiting does not preserve the status quo—the replacement spending continues.

Afilador múltiple de hojas de sierra Freedom
The promiseKeep cutting instead of leaving the jobsite.
Jobsite profit protection

The blade pile keeps growing. So does the replacement bill.

Every dull blade represents money already spent. Then another replacement gets opened, and the cycle starts again.

💵

1. They’re tired of buying blades over and over.

Blade costs add up fast — especially premium blades. Resharpen oscillating blades, hole saws, circular/miter saw blades, reciprocating blades, drill bits, and more so you get more life from what you already paid for.

  • Resharpens steel, bi-metal, and carbide blades
  • Refresh oscillating blades, hole saws, circular/miter saw blades, reciprocating blades, drill bits, and more
  • Build a backup pile of sharpened blades before the next blade run
  • Start cutting replacement-blade spending now
⏱

2. They’re tired of leaving the jobsite for blades.

A dull blade should not turn into a hardware-store run. When the blade starts smoking, skating, burning, or cutting slow, sharpen on site and keep the job moving.

  • Skip the hardware-store run
  • Keep your crew cutting
  • Protect the schedule when a blade goes dull
  • Stop losing momentum over replacement blades
JobSaver Pro turns that dead blade pile into ready-to-use working inventory. Use it on the job when a blade dies. Use it later to rebuild your blade stock instead of throwing money away.
Why act now?

The replacement bill keeps growing until you change the workflow.

Every blade thrown away while you wait to order is another blade you may end up paying to replace. The sooner JobSaver Pro is in your workflow, the sooner you can start reclaiming blades and keeping that money in the business.

Stop sending paid-for blade value to the trash or landfill. Reclaim it, sharpen it, and put it back into rotation.
Industry proof

Reviewed by trade publications contractors already trust.

Reviewed by Fine Homebuilding

Fine Homebuilding called the sharpener a “portable and precise” battery-operated solution and noted that sharpening an old blade did not take much longer than installing a new one.

Read the Fine Homebuilding review

Reviewed by Wood Floor Business

Wood Floor Business described the sharpener as “quick and easy to use” and reported that cutting new teeth into a dull blade took about 10 seconds.

Read the Wood Floor Business review
The Fixer YouTube review thumbnail for Tiger’s Teeth blade sharpenerWatch reviewer video

The Fixer put it to work.

The sharpener took a blade that was basically garbage and “resharpened it in 10 seconds.” It also “quickly pays for itself” and is “the real deal.” — The Fixer

Watch the YouTube review
Real customer proof

Contractors are buying it because the problem is real.

Real customer feedback helps prove this is not just a clever idea. It is a tool people are using to get more life from saw blades.

KW
★★★★★

“This tool is no joke.”

I was skeptical at first, but after sharpening a pile of blades, the tool did what it said. This is the kind of proof a contractor needs before trusting a new tool.

Keith W. · 2 Guys & a Hammer
TT
★★★★★

“It sharpens wood blades great.”

A customer reported sharpening wood blades and cutting into old, very dry oak siding — exactly the kind of real blade-use proof contractors care about.

Verified customer · Tiger’s Teeth review
JB
★★★★★

“Impressive.”

One customer reported bringing a batch of blades back instead of throwing them away, which is exactly the jobsite-saving idea behind JobSaver Pro.

Juan B. · Verified customer

Built by a small Michigan team

Tiger’s Teeth product image

Every unit is built by a small crew in Michigan. That is also why the current build time matters: high demand means units are built in the order received.

  • Built by hand in Michigan.
  • Worldwide shipping available.
  • 30-day money-back guarantee.

Customer reviews

Read more customer feedback from verified Tiger’s Teeth buyers.

Frequently Asked Questions

Everything you need to know before you sharpen your first blade.

What version do I need?

The Platinum Everything Package is the most popular and sharpens the widest range of blades. The Gold package includes two different 60-degree side grinding wheels for steel, bi-metal, and carbide touch-ups. The Basic is for those who just wish to sharpen steel or bi-metal oscillating multi-tool blades.

How long do the grinding wheels last?

Electroplated grinding wheels last a long time as long as they are not abused. Out of the many hundreds sold, only one customer has worn one out. I’ve sharpened a ton of blades and haven’t worn one out yet, so I can’t give an exact number. My CNC grinder uses similar electroplated grinding wheels, and they last for years.

Will the diamond version sharpen both steel and carbide blades?

Because this is high-speed grinding, steel reacts with diamond, turning it into carbon dust and wearing it out quickly. Only use diamond abrasive on carbide and CBN abrasive on steel or bi-metal.

Where are these made?

I and my small team make all of them individually in Michigan. By the way, thanks for supporting small business guys like myself!

Is a battery included?

A battery adapter of your choice is included. No battery or battery charger is included.

Does international shipping include import fees?

Shipping prices do not include import or customs fees and taxes. Shipping carriers will handle charging any import taxes once the shipment arrives in the destination country.

Afilador múltiple de hojas de sierra Freedom
Paquete Platino Todo / DeWalt 20v$299.00